1 Principles topenlarge
The one-third tubular plate, which is placed posterolaterally on the fibula in an antiglide position, indirectly reduces the fracture and acts as a buttress to resist the posterior and proximal displacement of the distal fragment.
Additionally, the main fracture can be compressed with a lag screw, inserted through the plate.
The third fragment, if large enough, can be fixed to the main lateral malleolar fragment with a cancellous lag screw. This technique is used for the three-part type of transsyndesmotic multifragmentary fracture, in which an oblique fracture of the fibula has occurred through the transsyndesmotic zone, and the tip of the proximal fragment ("ski tip") has fractured off.
AO teaching video: Type B Malleolar Fracture 44-B (2004)
AO teaching video: Malleolar-Fracture Type B (1988)
2 Patient preparation and approach top
The patient may be placed in the following positions:
For this procedure a lateral approach is normally used.
3 Preliminary reduction topenlarge
Preparation of the fracture site
Check that there are no fibers of the anterior fibular ligament trapped between the main fragments, particularly if there has been a bony avulsion of their attachment. This can be a cause of irreducibility of an apparent simple transsyndesmotic fracture.
Do not strip the periosteum more than necessary.
Preliminary reduction before plate application
Having released the third fragment from between the main fibular fragments as necessary, reduce the fracture by applying light longitudinal traction and rotating the foot internally.
4 Plate preparation topenlarge
Bending the plate
Prepare a four hole one-third tubular plate. To improve the anti-glide buttressing effect, the plate is slightly bent at its distal end.
This applies posterior compression on the distal fragment, which augments compression across the fracture plane.
Planning the plate position
Accurate positioning of the plate is essential in obtaining the desired buttress effect and allowing the insertion of a lag screw. The proximal hole closest to the fracture site should be located 3-5 mm proximal to the fracture line. Ensure that the lower end of the plate is not too distal, as, without the integrity of the "ski tip" of the proximal fibular fragment, a too distal point of pressure on the malleolar fragment risks tilting it anteriorly.
5 Fixation topenlarge
Reduce the main fragments and hold with a pointed reduction forceps. Ensure that the third fragment is reduced before tightening the forceps.
Either make sure the position of the forceps allows the plate to lie in the correct position, or alternatively, place the forceps through the hole in the plate before tightening the forceps.
In the proximal fibular fragment, drill a 2.5 mm hole through both cortices, from posterior to anterior, 3-5 mm proximal to the apex of the fracture.
Carefully position the plate so that two holes overlie each fragment, and hold it in place with a finger.
Insertion of the first proximal screw
Measure the length of the drilled hole through the plate.
Tap with the 3.5 mm cortical tap and insert the first 3.5 mm cortex screw.
Tightening the screw will push the plate against the fracture, holding it reduced.
Check reduction visually and under image intensification.
Insertion of the second proximal screw
Insert the second screw through the most proximal plate hole, drilling, measuring and tapping through the plate hole.
Prepare insertion of a lag screw
Drill a gliding hole through the plate hole closest and just distal to the fracture, using a 3.5 mm drill bit. The hole should be drilled as perpendicularly to the fracture line as possible.
Insert a 2.5 mm drill sleeve inside the gliding hole and drill the threaded hole in the far cortex with a 2.5 mm drill bit.
Measure the depth of the hole with the hook of the depth gauge pointing proximally.
Tap the far cortex with the 3.5 mm cortical tap.
Insertion of the lag screw
Insert a 3.5 mm cortical screw, functioning as a lag screw, and tighten carefully.
If the bone is osteoporotic, or if the fragment is large, a second cortical lag screw is inserted through the remaining distal plate hole.
Final x-rays should be taken now.
In less oblique fractures, or with a large third fragment, it is not possible to insert a lag screw. In this case you can omit the postero-anterior lag screw.
Fixation of third fragment
The final stage is the fixation of the third fragment to the main lateral malleolar fragment, using an anteroposterior cancellous lag screw, fitted with a washer.