As with any articular injury, anatomical restoration of the joint surface must be obtained. This is generally best done under direct vision, with clamp application, provisional fixation and then lag screw fixation.
The surgeon must bear in mind that the strong axial loading forces, as well as varus/valgus stress in the knee joint can tend to displace fragments. With vertical fracture lines, in particular, screw fixation alone may not be sufficient, and a buttress plate should be added.
Anatomy of the distal femur
The distal femur has a unique anatomical shape. Seen from an end-on view,
the lateral surface has a 10° inclination from the vertical, while the medial
surface has a 20–25° slope. A line drawn from the anterior aspect of the
lateral femoral condyle to the anterior aspect of the medial femoral condyle
(patellofemoral inclination) slopes approximately 10°. These anatomical details
are important when inserting screws. In order to avoid joint penetration,
screws should be inserted parallel to the patellofemoral and femorotibial joint
This procedure may be performed with the patient in one of the following positions:
For this procedure the following approaches may be used:
The standard lateral/anterolateral approach gives satisfactory joint exposure to check the quality of the joint reduction.
Remove the intraarticular hematoma and rinse the joint thoroughly with
Ringer lactate solution.
Reduce the fragment using a periosteal elevator and a ball-spiked pusher
(illustrated), or a dental pick.
Skin incision for pointed reduction forceps placement
Make a medial stab incision for the placement of the pointed reduction
Temporary fixation with K-wire insertion
Hold the final reduction using a large pointed reduction forceps. Make sure
to place the pointed reduction forceps not too posterior as compression across
the intercondylar notch would tend to tilt the fragment.
Secure the reduction with one, or more, temporary K-wires. Make sure that
the K-wire does not conflict with the planned screw track.
Check of reduction
The quality of the reduction is confirmed radiographically.
In general, the screws are inserted at points along the midshaft axis of the
femur (dashed line). The area distal to the Blumensaat’s intercondylar roof
line must be avoided in order not to violate the notch. In addition, the area
of the lateral knee recess should be avoided.
If you need to insert a screw in the area distal to the Blumensaat’s
intercondylar roof line, make sure to direct the screw anteriorly, in order to
avoid the intercondylar notch.
Insertion of guide-wires
Insert the appropriate guide-wires for 7.3 mm cannulated screws, or,
alternatively, 4.5 mm cannulated screws. Depending on the size of the fragment,
2 to 4 screws are necessary.
Guide-wire position check
Use the image intensifier to make sure that the tips of the guide wires just
penetrate the far cortex.
In good bone stock, you may now remove the pointed reduction forceps.
Otherwise, leave the pointed reduction forceps in place until all screws have
Pitfall: too long a guide wire
It is important to remember that the distal femur tapers from the posterior
to the anterior. Therefore, if a straight AP view is obtained, the guide wire
can appear to be inside the bone. If it appears to be outside the bone, it is
most likely too long. In order to assess the exact length of the guide wire
obtain an AP view with 30° internal rotation of the lower extremity.
In this illustration, internal rotation by 30° reveals that the guide wire
length was chosen inappropriately.
Screw length determination
Determine the appropriate screw lengths using the dedicated measuring
Predrilling is usually not necessary.
If it is planned to use a plate it is helpful to slightly countersink the
head of the most proximal screw. Manually insert the screws of appropriate
length over the guide-wire.
Washers are helpful if plate application is not planned, and always in
The temporary K-wire can now be removed.
Pearl: use temporary K-wire for further screw insertion
If you have used an appropriate K-wire size for temporary fixation of the
fracture, you can now insert an additional cancellous screw further to enhance
Irrigate all wounds copiously. Insert an intraarticular suction drain. Close the joint and the iliotibial tract using absorbable sutures. Close the skin and subcutaneous tissue in the routine manner.
Pearl: post-ORIF examination of knee joint stability under anesthesia
With the femur now stable, it is possible to perform a gentle examination of the knee joint to exclude associated ligamentous laxity, but be extremely careful testing with valgus stress.