Executive Editor: James Hunter

General Editor: Fergal Monsell

Authors: Andrew Howard, Peter Schmittenbecher, Theddy Slongo

Pediatric forearm shaft 22r-D/4.1

Open reduction; plate fixation

1. Introduction

General considerations

Plating is the standard technique for treating forearm fractures in adults and is therefore best considered for skeletally mature or nearly mature children.

Children with open physes have thick active periosteum favoring stability and rapid healing with the ESIN method. Where such techniques are unavailable plating may be used in younger children.

If technically possible, ESIN is biologically favored. If plating is used, soft-tissue and periosteal stripping should be minimized.

Plating of transverse forearm shaft fractures

Plating of pediatric forearm shaft fractures follows the technique for plate fixation in adults.

For transverse forearm shaft fractures, interfragmentary compression can be achieved with a compression plate.

This results in improved fracture stability.

2. Principles

Instruments and implants

A small fragment set consists of:

  • 2.7 or 3.5 mm plates and screws
  • Power driver
  • 2.7 or 3.5 mm insertion set
Compression

Axial compression results from eccentric screw (load screw) insertion with compression plates.

Prebending the plate

If the axial compression plate is exactly contoured to the anatomically reduced fracture surface, there will be gapping of the opposite cortex when the load screw is tightened.

The solution is to “over-bend” the plate so that its center stands off 1-2 mm from the anatomically reduced fracture surface.

When the neutral side of the plate is applied to the bone, slight gapping of the cortex will occur directly underneath the plate.

As the load screw is tightened, the tension generated in the plate compresses the fracture evenly across the full diameter of the bone.

Plate position

Depending on the surgical approach, the plate will be applied to either the anterior or posterior surface of the radius.

In the following example, a plate applied to the anterior surface is illustrated.

Plate contouring

The plate may need to be contoured to conform to the morphology of the radial shaft.

Choice of approach

For proximal radial shaft fractures, the anterior approach (Henry) is most often used to minimize the risk of damage to the posterior interosseous nerve, which crosses the proximal radius within the supinator.

In mid and distal radial shaft fractures, either the anterior approach (Henry) or posterolateral approach (Thompson) can be used, depending on the surgeon’s preference.

3. Patient preparation

This procedure is normally performed with the patient in a supine position .

4. Reduction

Reduction and fracture stability in children

Children’s periosteum is thick, tough tissue and is often intact on the concave (compression) side of a fracture.

Reduction maneuvers should be gentle to take advantage of the stability of an intact periosteum.

Exaggeration of the fracture deformity may be required to loosen the periosteum and allow gentle reduction.

In pediatric fractures there is often a combination of patterns of bone failure. Residual plastic deformity may prevent anatomical reduction of some of the fracture edges. Provided the alignment of the bone is anatomical and overall reduction is stable it is not necessary to perfectly reduce the entire fracture.

Open reduction

Reduce the fracture anatomically, using a reduction forceps on each main fragment.

The use of blunt, as opposed to pointed, reduction forceps can be helpful, particularly if greater forces are required.

Pearl: small bone lever

A small bone lever can be used to reduce transverse, or short oblique, fractures as illustrated.

Pearl: twisting a reduction forceps

Reduction of overlapping short oblique fractures can be achieved by twisting a reduction forceps, thereby lengthening the fracture.

Maintaining fracture reduction

A reduced transverse fracture cannot be maintained with reduction forceps alone.

However, transverse fractures are usually dentate and are intrinsically stable after anatomical reduction.

In children, interdigitation of the fracture fragments may be prevented by plastic deformity of the bone ends.

If unstable, fix the plate to one fragment and then reduce the other fragment onto the plate.

5. Plate length and number of screws

In the forearm, three bicortical screws are suggested in each main fracture fragment due to the high torsional stresses.

Not every plate hole needs to be occupied by a screw.

In short oblique forearm shaft fractures an empty plate hole may be necessary at the level of the fracture.

 

6. Fixation

Prebending the plate

After the plate has been contoured anatomically to the reduced bone surface, prebend it with the handheld bending pliers, or a pair of bending irons, as explained in the principles section.

Plate positioning

Make sure that the plate is seated on the bone without any soft-tissue interposition, apart from periosteum which should not be stripped.

In rare cases, the posterior interosseous nerve is visible. In such cases it is recommended that the position of the nerve in relationship to the plate be noted and documented in the operation report.

Insertion of 1st screw

Fix the prebent plate to one of the main fragments with a screw in neutral mode.

Place a reduction forceps on the opposite fragment to hold it in the reduced position against the plate.

Insertion of 2nd screw eccentrically

Insert a second screw eccentrically into the opposite fragment.

By tightening the eccentrically inserted screw, axial compression is achieved.

Insertion of additional screws

Additional screws in each fragment are usually inserted in a neutral position.

However, should it be necessary to increase the axial compression, a second screw can be inserted eccentrically into either fragment.

As the second eccentric screw is tightened, the first screw in the same fragment should be loosened slightly to allow the plate to slide on the bone.

Completed osteosynthesis

Before inserting additional screws check reduction of the fracture and rotation of the forearm.

All other screws are inserted in a neutral position and do not produce additional compression.

7. Final assessment

Check the completed osteosynthesis with image intensification. These images should be retained for documentation or alternatively an x-ray should be obtained before discharge.

Make sure that the plate is at the correct location, the screws are of appropriate length and the desired reduction has been achieved.

Stabilize the elbow at the epicondyles and check the forearm rotation.

Appendix

Shortcuts

Decision support

Contact | Disclaimer | AO Foundation

v1.0 2018-11-28