Executive Editor: Chris Colton

Authors: Florian Gebhard, Phil Kregor, Chris Oliver

Distal femur 33-C1 ORIF

back to skeleton

Glossary

1 Principles top

Anatomy of the distal femur enlarge

Anatomy of the distal femur

The distal femur has a unique anatomical shape. Seen from an end-on view, the lateral surface has a 10° inclination from the vertical, while the medial surface has a 20–25° slope. A line drawn from the anterior aspect of the lateral femoral condyle to the anterior aspect of the medial femoral condyle (patellofemoral inclination) slopes approximately 10°. These anatomical details are important when inserting screws, or blade plates. In order to avoid joint penetration, these devices should be placed parallel to both the patellofemoral and femorotibial joints planes.

The muscle attachments to the distal femur are responsible for the typical displacement of the distal articular block following a supracondylar fracture, namely shortening with varus and extension deformity. Shortening is due to the pull of the quadriceps and hamstring muscles, while the varus and extension deformity is caused by the unopposed pull of the adductors and gastrocnemius, respectively.

The popliteal vessels, the tibial nerve and the common peroneal nerve lie in close proximity to the posterior aspect of the distal femur. Because of this, vascular injuries occur in about 3% and nerve injuries in about 1% of fractures of the distal femur.


There are no significant arteries, veins, or nerves on the lateral side of the knee. enlarge

Neurovascular structures

There are no significant arteries, veins, or nerves on the lateral side of the knee.

There may be bleeding from the lateral genicular arteries, which will need to be controlled using diathermy.

At the posterior aspect of the knee lie the popliteal artery, nerve and vein. It must be borne in mind that these structures can be damaged by the injury, or can be damaged by the surgeon during the reconstruction.


Reduction of the metaphyseal/diaphyseal fracture component

Consideration must be given to fracture reduction in:

  • Varus/valgus
  • Flexion/extension
  • Internal/external rotation
  • Translation
  • Lengthening/shortening

Reduction can be performed with a single reduction tool (e.g., large distractor), or by combining several steps (for example fracture table +/- external fixator, +/- reduction via the implant, etc.) to achieve the final reduction.

The preferred method depends on the fracture and soft-tissue injury pattern, the chosen stabilization device and the experience and skills of the surgeon.

If a large fragment has separated from the fracture zone and impaled the adjacent muscle, direct reduction of that fragment may be required.


Image showing the cable method being used. enlarge

Biomechanics

It is very important to restore the biomechanical axis of the lower limb. The normal biomechanical axis follows a line from the center of the femoral head, through the center of the proximal tibia and then through the center of the ankle joint. This axis can be checked intraoperatively by using a piece of cable, such as the diathermy cord, to give an approximate estimate of the axis, as follows.

The biomechanical axis must be restored and care should be taken to ensure that there is no malrotation of the distal femur on the proximal femur.


The radiological landmarks are the center of the femoral head, the center of the knee and the center of the ankle joint. enlarge

If no traction table is used (i.e., using the freehand technique) the cable method may be used. In this technique, the electrocautery cord is held from the iliac spine across the patella to the cleft between the first and second toes. If rotation is correct, this cord will pass over the midline of the patella, and slightly medial to the tibial eminence.

Another method of assessing rotational reduction is to compare the cortical thickness above and below the fracture. If a shaft fracture is multifragmentary, the image intensifier cannot be used to compare cortical diameters on each side of the fracture.


Illustration of the longitudinal axes of the lower limb. enlarge

This Illustration shows the longitudinal axes of the lower limb.


Final osteosynthesis enlarge

Two main steps

In the treatment of C-type distal femoral fractures, the surgeon first reconstructs the distal femoral articular block. A reduction of the metaphysis/diaphysis is then performed before the DCS plate is positioned along the femoral shaft.


Various implants compared enlarge

Choice of implant

For retrograde femoral nailing to achieve adequate fracture stabilization, the fracture should be at least 6 cm from the joint line to achieve distal locking with two transverse screws or a screw and a spiral blade. In contrast, more distal fixation can be achieved with plates, or locked fixators. For example the distal most screws in a LISS plate, or a condylar plate, may be subchondral.

The distal-most fixation for various implants are:

  • LISS plate: subchondral
  • Condylar plate: subchondral
  • 95° angled blade plate: 1.5 – 2 cm
  • 95° dynamic condylar screws: 2 cm
  • Retrograde intramedullary nail: 6 cm (for 2 locking screws, or one locking screw and a spiral blade)

2 Reduction and fixation of the articular block top

enlarge

Reduction of the articular block

The chosen approach must adequately expose the articular surface of the distal femoral condyle. Reduction aids that are helpful include:

  • A 5.0 mm or 6.0 mm Schanz pin in the medial and/or lateral femoral condyle to act as a joystick.
  • Pointed reduction forceps, or large pelvic reduction clamps, to clamp from medial to lateral across the intercondylar split.

Pearl: combination of reduction aids
Attempts at reduction of the intercondylar split with the pointed reduction forceps alone are often unsuccessful, as rotational control of the femoral condyle is also needed. The use of the Schanz pin in conjunction with the pointed reduction forceps is therefore preferred.


enlarge

Provisional fixation

Before definitive fixation is undertaken, more than one clamp is applied. Usually, one to two additional K-wires are inserted, either from medial to lateral, or lateral to medial.

If the K-wires are inserted from medial to lateral, they may either go through small stab incisions in the skin, or through the parapatellar retinaculum.


enlarge

Definitive articular surface fixation

Screws may be placed along the periphery of the articular surface of the lateral femoral condyle going from lateral to medial to compress the intercondylar split.

These screws may be fully threaded 3.5 mm lag screws (shown with gliding hole), 6.5mm partially threaded lag screws, or 4.0/4.5 mm cannulated, partially threaded lag screws.

Insertion of screws in this manner leaves a „free zone“ of bone into which a laterally based plate system can be inserted (dotted circle).


enlarge

This end-on view demonstrates the screw trajectories from lateral to medial.

On occasions, it is acceptable to insert screws through the articular surface, when no other option is available. These screws must be countersunk and recessed beneath the articular surface.

3 DCS fixation to the distal fragment top

Determine the correct position for the DCS with the help of guide wires around the joint. enlarge

Preparation for correct positioning

Determine the correct position for the DCS with the help of guide wires around the joint. Under image intensifier control, pass one guide wire lateral to medial along the tibio-femoral joint line (red). Pass a second guide wire over the anterior surface of the knee to indicate the plane of the patello-femoral condyles (green).

The ideal position of the DCS is shown by the yellow wire. Note that it is inserted parallel to both the red wire in the frontal plane and is parallel to the green line on the end-on view on the femur. This latter orientation ensures that the plate comes to lie flush with the lateral cortex.


The ideal entry point for the DCS is shown on the diagram. enlarge

The ideal entry point for the DCS is shown on the diagram. The guide wire for the DCS is positioned at 2 cm proximal to the distal end of femur. On the lateral view, the distal femur is divided into thirds and the DCS entry site is located at the junction of the anterior and middle thirds.

Insert the guide wire at the chosen entry site of the DCS. Insert the guide wire under image intensifier control all the way across the femur. Check the position of the guide wire carefully to ensure it has been correctly positioned, with the parallelism already described.


The tip of the guide wire should just engage the medial cortex. enlarge

Correct depth of guide-wire insertion

The depth of guide-wire insertion is crucial. Remember that the cross section of the distal femoral condylar mass is trapezoidal and slopes markedly on the medial side. The tip of the guide wire should just engage the medial cortex, and so will appear short of the medial condylar cortex on the AP intensifier image.


Correct guide-wire insertion depth. enlarge

Pitfall: too long a guide wire
It is important to remember that the distal femur tapers from the posterior to the anterior. Therefore, if a straight AP view is obtained, the guide wire can appear to be inside the bone. If it appears to be outside the bone, it is most likely too long and the DCS will cause pain and possibly heterotopic ossification. In order to assess the exact length of the guide wire obtain an AP view with 30° internal rotation of the lower extremity.


Incorrect guide-wire insertion. enlarge

In this illustration, internal rotation by 30° reveals that the guide wire length was chosen inappropriately.


Measuring for screw length. enlarge

Screw length measurement

Next, slide the direct measuring device over the guide wire and determine guide-wire insertion depth and, thereby, the length of the DCS required.


Reaming. enlarge

Reaming

After assembling the DCS triple reamer and setting the reamer to the correct depth, ream the hole for the DCS over the guide wire.


Inserting the DCS. enlarge

DCS insertion

After tapping, insert the DCS over the guide wire, so that its outer end is still visible 2-3 mm outside the lateral cortex of the distal femur.

In order for the plate barrel to slide over the screw, the T-handle should be parallel, on the lateral view, to the long axis of the distal fragment.

Pearl: omit tapping in osteoporotic bone
In osteoporotic bone, tapping should be omitted.


Passiong the plate barrel over the screw shank. enlarge

Plate placement

Detach the T-handle and pass the plate barrel over the screw shank.

Alternative: reconnect T-handle to screw
Some surgeons reconnect T-handle to the screw to help to adjust the position the plate. However, this maneuver is not absolutely necessary and some surgeons do not perform it.


Using the impactor to bring the plate down to the bone. enlarge

Plate impaction

Use the impactor to bring the plate down to the bone, with the barrel sliding over the screw shank.

The compression screw may be utilized to couple the screw to the plate.

Additionally, the compression screw will provide additional compression across the intraarticular split.

Pearl: do not use compression screw in osteoporotic patients
Do not use the compression screw in osteoporotic patients – it can cause the DCS thread to strip out from the soft cancellous bone of the medial femoral condyle.


Insertion of a screw to prevent rotation of the distal femoral articular block around the axis of the DCS. enlarge

Final screw placement in distal fragment

A cancellous screw can then be inserted into the most distal screw hole of the plate to prevent rotation of the distal femoral articular block around the axis of the DCS.

4 Plate fixation to the proximal fragment top

Using the articulated tension device enlarge

Reduction of metaphyseal fracture component

The key concept in reduction of the metaphyseal fracture component when utilizing a DCS is that insertion in the distal femur allows the surgeon to use the plate to assist the metaphyseal fracture reduction. The surgeon must control for length, rotation and sagittal plane deformity (hyperextension/hyperflexion). When performed in an open manner, length can be restored by manual traction. The sagittal plane deformity correction can be aided by a supracondylar bolster.

Loosely secure the plate to the proximal femur with a Verbrugge clamp.

Take care to restore the mechanical axis of the femur in all planes. Give consideration to fracture reduction in:

  • Varus/valgus
  • Flexion/extension
  • Internal/external rotation
  • Translation
  • Lengthening/shortening

Use of the articulated tension device
Secure the articulated tension device to the proximal femur with a bicortical screw.

The articulated tension device is very useful to apply controlled compression to the fracture site. It should be used when possible in fracture patterns where there is contact between the proximal and distal main fragments. It may not be used in situations of severe metaphyseal comminution and/or osteoporosis.


Eccentric screw insertion enlarge

Insertion of first screw into proximal fragment

Tighten the articulated tension device with the spanner so that the indicator on the tension device is in the green zone, checking the fracture site carefully to ensure that no unwanted displacement occurs.

Insert a screw through the plate close to the compression device to secure the fixation. Insert the screw eccentrically in the plate hole to maintain the fracture compression.

Complete the fixation of the plate to the femur with sufficient screws, using neutral insertion of the screws in the plate holes.


Completed osteosynthesis enlarge

Additional screw insertion

Lastly remove the articulated tension device and complete the fixation by inserting additional screws according to the preoperative plan.

v1.0 2016-10-19