1 Principles topenlarge
Classification of avulsion fractures of the volar plate
Avulsion fractures of the volar plate are very common injuries, often
resulting from sporting injuries and usually involving the middle and ring
fingers. Several classification systems for them have been proposed. The Eaton
classification is very useful for practical purposes. This classification is
based on the premise that successful treatment must be based on the stability
of the fracture, which in turn depends on
- size of the fragment
- degree of impaction,
- presence of one or both collateral ligament ruptures
- direction of the dislocation (hyperextension, lateral dislocation, flexion).
Eaton type I (hyperextension)
These are hyperextension injuries, with an avulsion of the volar plate and a longitudinal split in the collateral ligaments.
Eaton type II (dorsal dislocation)
Complete dorsal dislocation of the PIP joint and avulsion of the volar plate. The base of the middle phalanx rests dorsally on the condyles of the proximal phalanx, with no contact between the articular surfaces.
Eaton type III (fracture dislocation)
A fracture dislocation with a small fragment measuring less than 40% of the palmar arc will remain stable when reduced.
If a larger part (>40%) of the palmar articular segment is involved, ligamentous support will not suffice for a stable reduction.
Stability of fracture dislocations (Eaton type III)
Stability of the reduction depends on the size of the avulsed fragment and
the amount of ligament remaining attached to the middle phalanx.
If less than 40% of the articular segment is avulsed, the fracture is displaced dorsally, with the dorsal portion of the collateral ligament remaining attached to the middle phalanx. This helps to keep the reduction stable.
However, if more than 40% of the articular segment has avulsed, only very little or no ligament will remain attached to the base of the middle phalanx, rendering the reduction unstable.
Mechanism of the injury
These injuries are commonly caused by sporting accidents.
Typically, hyperextension of the finger causes an avulsion fracture of the volar plate.
Often, in addition to hyperextension, pressure is applied to the fingertips, causing longitudinal compression forces on the middle phalanx towards the proximal phalanx and leading to an additional impaction fracture.
The flexor digitorum superficialis (FDS) exerts a palmar pull on the middle phalanx around a pivotal point determined by the junction of intact cartilage and the fracture, which leads to subluxation and dorsal tilting, depending on the degree of the impaction.
Diagnosis is based on
- the clinical history of the trauma and mechanism of the injury
- the clinical examination of the patient
- the x-rays
AP and lateral x-rays are necessary for diagnosis. Be careful to avoid
interposition of other fingers in the x-rays.
An AP view will help to recognize impaction fractures.
Often, a subluxation is not apparent on the lateral view. Look for the characteristic “V” sign of diverging joint surfaces, which indicates this injury.
In the lateral view, the proximal and middle phalanges should be collinear. Any axial malalignment is a clear indication of subluxation.
2 Indications topenlarge
Indication for nonoperative treatment
Ask the patient to flex the finger under image intensification.
If reduction of the avulsion fracture is achieved with less than a 30 degree bend, nonoperative treatment may be a good choice.
However, if it takes more than 30 degrees of bending, operative treatment is indicated.
Reduction will not be achieved if tissues are interposed between the fracture fragments. This, too, is an indication for surgical treatment.
Passive lateral movement of the finger under image intensification will help to assess lateral stability.
Small-fragment avulsion fracture
When the avulsed fragment is very small (<30% of the articular segment), nonoperative treatment is usually a good choice.
Irreducible fracture – operative treatment
In some cases, the fracture can not be reduced due to interposed tissues, or
In these cases, internal fixation is indicated.
As the use of a lag screw could easily shatter a small fragment, internal fixation with sutures is a good choice in such fractures.
3 Visualize the Joint topenlarge
Hyperextend the middle phalanx to gain a maximal view of the joint.
In order to gain better view of the fracture, use a syringe to clear out blood clot with a jet of Ringer lactate.
Assess fracture geometry and look for comminution or impaction, which may not be apparent from the x-rays and can only be determined under direct vision.
4 Fixation topenlarge
Keeping the phalanx hyperextended, drill holes for the needles in the ulnar
and radial sides of the in the base of the middle phalanx.
Each drill hole must be placed halfway between the palmar and dorsal edges of the fracture surface
It is mandatory to use a drill guide to protect the cartilage of the condyles.
The drill holes must perforate the dorsal cortex of the middle phalanx.
Always choose the diameter of the drill holes corresponding to the width of the small avulsed fragment. If the drill holes are too small, reduction may be prevented by interposing sutures.
Make a dorsal incision of about 1 cm, distal to the insertion of the central slip, incising the triangular ligament.
Use 4.0 multifilament nonabsorbable sutures with double-mounted straight
Wrap each suture around the small fragment attached to the volar plate, and insert the two ends of each suture through its drill hole. Both needles should exit dorsally through the skin incision.
Now gently reduce the fracture by pulling on the sutures in a dorsal
Confirm anatomical reduction using image intensification.
Tighten the sutures
After confirming that the volar plate is not too short, and that fixed
flexion does not exceed 30 degrees, tighten the sutures over the dorsal cortex
of the middle phalanx.
Resuture the triangular ligament, if possible.
5 Alternative fixation topenlarge
Alternatively to the described method, suture anchors can be used.