1 Principles topenlarge
When vertical compression forces, created by axial load, are applied to the
finger, comminuted, intraarticular, compression fractures may result. These
fractures are very unstable.
Typically, they occur in two configurations:
- as centrally impacted, comminuted fractures, or
- with a T- or Y-type fracture geometry.
It is desirable to obtain stable fixation to allow early motion and to minimize the risk of degenerative joint disease.
2 Reduction topenlarge
Compression fractures are not reducible by ligamentotaxis, as the centrally
impacted fragments are devoid of soft-tissue attachments.
Direct reduction is therefore necessary.
The key to fixing compression fractures is restoring the joint surface to as close as normal as possible, and supporting the reduction with bone graft and internal fixation.
Disimpact the fragments
Using a K-wire, or dental pick, the fragments are disimpacted and pushed
towards the head of the metacarpal, which is used as a template to ensure
congruity of the articular surface of the phalanx.
If a cartilage step-off greater than 1 mm remains, degenerative joint disease may follow.
Since the metaphyseal cancellous bone is impacted, a void may be created by
This jeopardizes the fracture in two ways:
- this is a very unstable situation in which the fragments may easily
- the healing process is delayed.
3 Bone graft topenlarge
Cancellous autograft, or very occasionally bone substitutes (e.g. hydroxyapatite, tricalcium phosphate) will be necessary to support the articular fragments and fill the impaction void. The graft will also enhance the healing process.
Preparation of the bone graft
Cancellous bone is harvested from the distal radius or the iliac crest. It is then chopped into tiny pieces and filled into a syringe.
Impact the bone graft
Impact the bone graft using a mallet to compress the syringe plunger. This results in a high concentration of bone cells, increasing the potential for bone regeneration and healing.
Insert graft into cavity
The bottom of the syringe is cut off using a scalpel.
Insert the compacted bone graft into the cavity by pressure on the plunger.
Using a blunt dissector, impact the bone graft and fill the whole fracture cavity.
4 Plate preparation topenlarge
Two types of plate are available for treatment of this fracture:
- 1.5 Minicondylar plate
- 1.3 or 1.5 T-plate (adaption plate)
Select a plate according to fragment size, fracture geometry, and surgeon‘s preference.
Measure for length of the blade
Measure the length of the drill hole using a measuring device.
Cut the blade to the determined length, so that it just fills the drill hole.
Avoid protrusion from the opposite cortex, as friction during movement and eventual ligament injury may result.
Trim the plate
Adapt the plate length to fit the length of the proximal phalanx. Avoid
sharp edges which may be injurious to the tendons. There should be at least 3
plate holes distal to the fracture available for fixation in the diaphysis. At
least two screws need to be inserted into the diaphysis.
Pearl: Cut the blade transversely
If you cut the blade on the flat, it will compress and widen very slightly as it is cut. This makes its maximal width very slightly larger than 1.5 mm. It may not fit in the 1.5 mm hole that you have drilled.
Therefore, cut the blade on edge (to deform it through its narrower dimension) to the correct length. The resultant tip is somewhat arrow-shaped.
Contouring of the plate
Use pliers to contour the plate so that it fits exactly the anatomy of the
base of the proximal phalanx.
The plate was designed for condylar fractures and is precontoured to fit around a condyle. It has to be adapted for the less curved shape of the base of the proximal phalanx.
5 Fixation topenlarge
Determine location of drill hole
In order to determine the position of the first drill hole, it can be very helpful to turn the plate over and use it as a template ...
... as shown in this clinical photo.
Drill a 1.5 mm transverse hole through the base of the proximal phalanx adjacent to the joint surface as a track for the blade of the plate.
The drill hole needs to be dorsal enough as to leave enough space for the plate’s most proximal screw hole.
Introduce the blade into the drill hole. Gently push with the thumb until the plate is fully seated.
Align the plate with the diaphysis
Before inserting the first (distal) screw, ensure that the plate is in line with the phalangeal diaphysis in the sagittal plane by rotating it around the axis of the blade.
Drill a distal hole
Use a 1.1 mm drill bit to prepare the first neutral screw hole at the distal end of the plate.
Measure for screw length and insert a self-tapping 1.5 mm screw.
Insert proximal screw
The proximal screw is inserted next, in the same fashion.
The screws should just engage the far cortex. This proximal screw functions as a position screw only.
Do not exert compression through this screw, as this may compromise the reduction of the comminuted zone.
Be careful to avoid protrusion of the proximal screw through the far (trans) cortex, as ligament injury may result from friction during movement.
Insert further screws into the diaphyseal holes in a neutral position to finalize fixation.