Annual Report

Executive Editor: Rick Buckley, Chris Colton

Authors: Florian Gebhard, Phil Kregor, Chris Oliver

Patella Extraarticular avulsion fracture

back to skeleton

Glossary

1 Principles top

There exist circumstances in which the patellar fragments cannot be reduced adequately and when function of the extensor apparatus remains compromised. Patella tendon repair can produce acceptable results. The secret is attention to operative detail by a skilled surgeon.

2 Patient preparation and approach top

enlarge

Patient preparation

This procedure is normally performed with the patient in a supine position with the knee flexed 30°.


enlarge

Approach

For this procedure a mid-axial longitudinal approach is used.

3 Debridement top

enlarge

The knee joint and fracture lines must be irrigated and cleared of blood clots and small debris to allow exact reconstruction.

4 Patellar tendon repair and augmentation top

enlarge

Patellar tendon repair

If the patellar tendon has been torn from the distal pole of the patella the extensor mechanism must be repaired, to regain active knee extension.

Suture the patellar tendon to the patella with 5 nonabsorbable transosseous sutures.

This repair needs augmentation with a patello-tibial wire because it is never strong enough to sustain knee flexion extension forces.


enlarge

Augmentation using cerclage wire around the patella

After the patellar tendon has been repaired, or if fixation of the patellar tendon origin is inadequate, because of multiple, small fragments, the transosseous sutures must be protected with a cerclage wire between patella and tibial tuberosity.

The anchoring at the tuberosity can be achieved with a simple figure-of-zero cerclage wire through a transverse drill hole just below the tibial tuberosity.

When tightening the loop, it is necessary to ensure that the knee can flex at least to 90°. This means that in full extension there will be some laxity of the cerclage wire.

The same technique can also be used in very small avulsion fractures.


enlarge

Protection wire in place postoperatively in a patient with a multifragmentary inferior pole of patella where the tendon was stitched back to the patella. The wire protects the soft tissue repair.


enlarge

This image shows the inferior multifragmentary pole of patella has been removed. The tendon has been stitched with the appropriate of patella height using the Salvati ratio.


enlarge

Three months later the wire was removed with the healed tendon ready to take more biologic forces without protection.


enlarge

Three months lateral X-ray showing a well-positioned patella after patellar tendon reconstruction and protection wire placement (wire has been removed at three months).


enlarge

As an alternative in osteoporotic bone, the anchorage at the tuberosity can be achieved around a 3.5 mm cortex screw, or through the hole of a cannulated screw.


enlarge

It is the surgeon’s decision whether a figure-of-zero, or figure-of-eight, loop is made, based on personal experience and preference.


enlarge

Pitfall: If the cerclage wire is tensioned too tightly it will not be possible to flex the knee and a patella baja will occur.

This complication must be avoided as it can cause severe limitation of knee flexion and anterior knee pain. If there is need for a cerclage wire to protect the patellar tendon, a patella baja can be produced by misjudging the exact length of the patellar tendon. The opposite knee will indicate the correct position of the patella, as revealed by x-ray evaluation.


enlarge

Augmentation using cerclage wire through the patella

Use a patellotibial cerclage wire between the patella and tibial tuberosity to augment the repair. The anchoring at the tuberosity can be achieved around a 3.5 mm cortex screw, or through the hole of a cannulated screw. When tightening this, ensure that the knee is able to flex to 90°. This means that in full extension there will be some laxity of the cerclage wire.

Pearl: One way to ensure that the patellofemoral biomechanics are restored to more functional normality is to position the cerclage wire in a more anatomical position. It is preferable to pass the cerclage wire transversely through the middle, or lower, third of the patella. If the cerclage wire is passed over the proximal pole of the patella this tends to cause increased patellofemoral flexion load, which may lead to anterior knee pain.

5 X-ray control top

The result is checked in the AP and lateral planes using an image intensifier.

After a patellar tendon repair, a lateral X-ray should be taken and compared to the normal knee to ensure patellar height is very similar to the uninjured knee.

v2.0 2019-03-21