Executive Editor: Fergal Monsell General Editor: Chris Colton

Authors: Andrew Howard, James Hunter, Theddy Slongo

Pediatric proximal femur 31-M/3.1 I

back to Pediatric overview

Glossary

1 Preliminary remarks top

enlarge

Introduction

Children's hip fractures have historically had a bad prognosis. Accurate stable fixation has been one of the factors identified to improve the outcome.

Stable fractures have a better prognosis than displaced fractures.

The main problems have been avascular necrosis (AVN) due to disruption of the blood supply, nonunion and malunion due to unstable fixation.

The objective is timely fixation without disruption of the blood supply.


enlarge

Equipment selection

6.5, 7.0, or 7.3 mm cannulated screws are used for adolescents.

4.5, or 4.0 mm cannulated screws may be selected for younger children. Be aware that these screws are considerably weaker and prone to breakage if used in too heavy a child.

Washers are optional depending on the strength of the bone.


enlarge

Implant insertion

Typically, two screws separated vertically are inserted. This configuration may be more suitable in smaller bones.

An alternative is three screws used in an apex-distal, triangular configuration, with the lower central screw abutting the calcar.

Inserting a single central screw does not provide rotational stability and is, therefore, less applicable for fractures, even though it is a common choice for SCFE.

The combination of the child's age and the position and orientation of the fracture line will determine whether lag screw fixation can be obtained.


enlarge

Pitfall: Secondary subtrochanteric fractures may occur if screws are placed below the level of the lesser trochanter.


enlarge

For children with 4 or more years of growth remaining, techniques that allow continuous growth of the physis should be considered.

These techniques include:

Metaphyseal only fixation if the fracture pattern allows

Fixation across the growth plate with threaded screws that are removed promptly after fracture healing

Note: It is more important to achieve fracture stability than to avoid crossing the physis.


enlarge

Cannulated screws alone may not provide adequate stability for a vertically oriented fracture line. A pediatric hip locking plate is a better construct if the fracture line is more vertical.

2 Reduction top

enlarge

A guide wire is inserted through the lateral cortex of the femur just above the level of the lesser trochanter and advanced to the fracture line.

If necessary, manipulation of the femoral head is achieved using a small K-wire, inserted into the proximal fragment, as a joystick.


enlarge

The femoral neck is manipulated gently into position, usually by lifting with a bone hook and manipulating the wires.

Gentle reduction maneuvers are essential in order to prevent secondary damage to the femoral head blood supply.


enlarge

When acceptable reduction has been obtained, the first wire is advanced across the fracture and into the femoral head. Overpenetration into the hip joint should be avoided.

3 Fixation top

enlarge

Insertion of additional guide wires

Additional guide wires are inserted under x-ray control using image intensification according to the two, or three screw configuration desired.


enlarge

X-ray control

The guide wire positions are confirmed on AP and lateral x-rays, using image intensification.


enlarge

If using a regular radiolucent table, the guide wire fixation is generally stable enough to allow "frog" lateral view.

The guide wires are repositioned if necessary.


enlarge

Images at multiple angles are used to confirm that the guide wires do not penetrate into the hip joint.


enlarge

Measuring screw length

A depth gauge is used to measure screw length.

If a dedicated cannula/depth gauge set is not available, then a K-wire, of the same length as that inserted, is placed onto the lateral cortex adjacent to the inserted wire, and the difference measured to determine the screw length.

If the screw is being used to lag against the lateral cortex, 5mm is subtracted to avoid screw overpenetration.


enlarge

Drilling screw holes

The guide wires are overdrilled with the appropriately sized cannulated drill bit.

Adolescents in particular have very dense bone in the metaphysis near the growth plate and predrilling of both sides of the fracture line is recommended.

If cannulated screws are not available, then guide wires should be removed one at a time and an appropriate drill used.


enlarge

Screw insertion

Two or three cannulated screws are inserted over the guide wires.

The use of washers is optional.


enlarge

X-ray control

Image intensification is used to confirm that the screw tip does not penetrate into the hip joint.

Typically, 5 mm of epiphyseal bone/cartilage should remain between the screw tip and joint surface.

Pitfall: Screw penetration can occur, especially with eccentrically placed screws, even if not apparent on AP or lateral x-rays.

Dynamic, real-time image intensification, with a full range of internal and external rotation at different degrees of flexion, is useful to see how close the screw-tip is to the joint surface of the femoral head.

Observing an approach/withdrawal of the screw tip helps in judging its position. Some surgeons supplement this examination with 3-D image intensification for confirmation.

Arthrography is useful to confirm correct screw placement in the younger patient.


enlarge

Guide wire removal

Guide wires are removed.

4 Hip spica top

enlarge

If solid fixation has been obtained with screws, and the patient/family can reliably comply with toe-touch weight bearing, then a cast is not necessary.

For patients below 5 years of age, a hip spica cast can be used if desired.

Click here for details of hip spica application.

v1.0 2017-12-04