Executive Editor: James Hunter General Editor: Fergal Monsell

Authors: Andrew Howard, Peter Schmittenbecher, Theddy Slongo

Pediatric forearm shaft 22-D

back to Pediatric overview

Glossary

1 Note on illustrations top

Generic fracture patterns enlarge

Throughout this section generic fracture patterns are illustrated as:

A) Unreduced
B) Reduced
C) Reduced and provisionally stabilized
D) Definitively stabilized

2 General considerations top

Combination of external fixator and ESIN enlarge

External fixation of both bones is uncomfortable and technically demanding but occasionally indicated particularly with crush injuries with extensive soft-tissue damage and skin loss.

The external fixator may be applied to a single bone with the second bone stabilized with ESIN.

External fixation of the ulna is less demanding with accessible safe zones.


ESIN fixation of the radius enlarge

ESIN fixation of the radius

The steps required for radial fracture fixation are described in the ESIN procedures for each fracture type:


ESIN fixation of the ulna enlarge

ESIN fixation of the ulna

The steps required for ulnar fracture fixation are described in the ESIN procedures for each fracture type:

3 Principles of modular external fixation top

Modular external fixator enlarge

Modular external fixator

The versatility of a modular external fixator is an advantage in the management of children’s fractures and can accommodate age specific variations in fracture biology and anatomy.

An external fixator may be used for definitive management of forearm fractures in children due to the short healing time.

Practical considerations are illustrated in detail in the Basic technique for application of modular external fixator in children.

Specific considerations for the forearm shaft are given below.


Other types of external fixator enlarge

Other types of external fixator

Alterative configurations are available and include monolateral or ring systems.

Disadvantages of these systems in children include:

  • Fixed distance of pin insertion defined by the clamp
  • Excessively stiff construct

Pin size in forearm fractures

External fixation is suitable for all ages, but the pin diameter must be appropriate to the size of the bone.

Pins with a thread diameter of 2.5-4.0 mm are suitable for forearm fractures and should be about 1/3 of the bone diameter.


Sequence of pin insertion

Determined by:

  • Fracture morphology
  • Personal preference

4 Sequence of fixation (forearm shaft) top

Sequence of fixation enlarge

In both bone fractures, it is usually more straightforward to apply the initial external fixator to the less complex fracture.

This series illustrates external fixation of the ulna before the radius.

For clarity, the external fixator on the ulna is omitted from the illustrations of fixation of the radius.

5 Frame construction on the ulna top

Proximal pin insertion enlarge

Proximal pin insertion

Insert the proximal ulnar pins through the subcutaneous cortex of the posterior border of the ulna between the extensor and flexor muscle masses.


Proximal pin insertion enlarge

Make an 8-10 mm skin incision over the site of pin insertion.

Use an artery clip for blunt dissection down to the bone, protecting important anatomical structures.


Proximal pin insertion enlarge

The posterior border of the ulna is subcutaneous and offers the best access.

Insert the pin in the near cortex and through the center of the bone into the far cortex.

Take care not to advance the tip of the pin beyond the far cortex to avoid damage to neurovascular structures.

Pins should not be placed closer than 1 cm to the physis.


Distal pin insertion enlarge

Distal pin insertion

Safe access to the subcutaneous dorsomedial cortex is improved with the elbow flexed and the forearm in mid-supination.


Distal pin insertion enlarge

Make an 8-10 mm skin incision over the site of pin insertion.

Use an artery clip for blunt dissection down to the bone, protecting important anatomical structures.


Distal pin insertion enlarge

Insert the distal ulnar pins from dorsomedially between the extensor carpi ulnaris and flexor carpi ulnaris.

As the distal ulna in children has a small diameter, oblique pin placement improves bony contact.

Pins should not be placed within 1 cm of the physis.

6 Frame construction on the radius top

Distal pin insertion enlarge

Distal pin insertion

In the distal 1/3 of the forearm, the pin is inserted via a dorsolateral incision with blunt dissection to bone. Pins are inserted under direct vision, using retractors to avoid the superficial branch of the radial nerve. The pin passes between the extensor pollicis longus (EPL) and the extensor carpi radialis or more laterally between extensor carpi radialis and the tendon of brachioradialis.


Distal pin insertion enlarge

Make an 8-10 mm skin incision over the site of pin insertion.

Use an artery clip for blunt dissection down to the bone protecting important anatomical structures.


Distal pin insertion enlarge

Insert the pin in the near cortex and through the center of the bone into the far cortex.

Take care not to advance the tip of the pin beyond the far cortex to avoid damage to adjacent neurovascular structures.

Pins should not be placed within 1 cm of the physis.


Proximal pin insertion enlarge

Proximal pin insertion

The most critical anatomical consideration in the proximal 1/3 of the radius is the position of the posterior interosseous nerve, a continuation of the deep branch of the radial nerve, which perforates the supinator.

The dissection for the pin must be distal to the radial tuberosity and pass between the extensor carpi ulnaris and the mobile wad, penetrating the supinator muscle near its ulnar insertion.


Proximal pin insertion enlarge

A longer incision and blunt dissection to the bone is recommended to avoid damage to the posterior interosseous nerve.

Make a 1-2 cm skin incision over the site of pin insertion.

Use an artery clip for blunt dissection down to the bone, protecting important anatomical structures with small retractors.

Depending on the length of the proximal fragment, the distal pin may be positioned distal to the insertion of the supinator. This pin should also be inserted under direct vision.


Proximal pin insertion enlarge

Insert the pin in the near cortex and through the center of the bone into the far cortex.

Take care not to advance the tip of the pin beyond the far cortex to avoid damage to adjacent neurovascular structures.

Pins should not be placed within 1 cm of the physis.

7 Assessment of fracture reduction top

Once the fracture is reduced and stabilized, the alignment and position of the pins may be checked with an image intensifier.

v1.0 2018-11-28