Executive Editor: James Hunter General Editor: Fergal Monsell

Authors: Andrew Howard, Peter Schmittenbecher, Theddy Slongo

Pediatric forearm shaft 22u-D/4.1

back to Pediatric overview

Glossary

1 Introduction top

General considerations

Plating is the standard technique for treating forearm fractures in adults and is therefore best considered for skeletally mature or nearly mature children.

Children with open physes have thick active periosteum favoring stability and rapid healing with the ESIN method. Where such techniques are unavailable plating may be used in younger children.

If technically possible, ESIN is biologically favored. If plating is used, soft-tissue and periosteal stripping should be minimized.


Plating of transverse forearm shaft fractures enlarge

Plating of transverse forearm shaft fractures

Plating of pediatric forearm shaft fractures follows the technique for plate fixation in adults.

For transverse forearm shaft fractures, interfragmentary compression can be achieved with a compression plate.

This results in improved fracture stability.

2 Principles top

Instruments and implants enlarge

Instruments and implants

A small fragment set consists of:

  • 2.7 or 3.5 mm plates and screws
  • Power driver
  • 2.7 or 3.5 mm insertion set

Compression enlarge

Compression

Axial compression results from eccentric screw (load screw) insertion with compression plates.


Prebending the plate enlarge

Prebending the plate

If the axial compression plate is exactly contoured to the anatomically reduced fracture surface, there will be gapping of the opposite cortex when the load screw is tightened.

The solution is to “over-bend” the plate so that its center stands off 1-2 mm from the anatomically reduced fracture surface.

When the neutral side of the plate is applied to the bone, slight gapping of the cortex will occur directly underneath the plate.

As the load screw is tightened, the tension generated in the plate compresses the fracture evenly across the full diameter of the bone.


Plate position enlarge

Plate position

The ulnar plate can be positioned under the extensor carpi ulnaris (A), under the flexor carpi ulnaris (B), or in the interval between extensor and flexor carpi ulnaris (C).

With a more proximal fracture it can be more difficult to place the plate underneath the extensor muscle.

With more distal fractures, plates should be placed in the interval between the extensor and flexor carpi ulnaris (C).

Plating the tensile (subcutaneous) aspect of the ulna (C) is biomechanically preferable, but plate prominence can cause irritation.

Plates in positions A or B are covered by the muscle compartment and avoids this complication.

In the following procedure, the plate positioned on the subcutaneous border of the ulna (C) is illustrated.

3 Reduction top

Periosteum as a factor in reduction enlarge

Reduction and fracture stability in children

Children’s periosteum is thick, tough tissue and is often intact on the concave (compression) side of a fracture.

Reduction maneuvers should be gentle to take advantage of the stability of an intact periosteum.

Exaggeration of the fracture deformity may be required to loosen the periosteum and allow gentle reduction.

In pediatric fractures there is often a combination of patterns of bone failure. Residual plastic deformity may prevent anatomical reduction of some of the fracture edges. Provided the alignment of the bone is anatomical and overall reduction is stable it is not necessary to perfectly reduce the entire fracture.


Open reduction with forceps enlarge

Open reduction

Reduce the fracture anatomically, using a reduction forceps on each main fragment.

The use of blunt, as opposed to pointed, reduction forceps can be helpful, particularly if greater forces are required.


Open reduction with bone lever enlarge

Pearl: small bone lever

A small bone lever can be used to reduce transverse, or short oblique, fractures as illustrated.


Open reduction by twisting a reduction forceps enlarge

Pearl: twisting a reduction forceps

Reduction of overlapping short oblique fractures can be achieved by twisting a reduction forceps, thereby lengthening the fracture.


Maintaining fracture reduction enlarge

Maintaining fracture reduction

A reduced transverse fracture cannot be maintained with reduction forceps alone.

However, transverse fractures are usually dentate and are intrinsically stable after anatomical reduction.

In children, interdigitation of the fracture fragments may be prevented by plastic deformity of the bone ends.


Maintaining fracture reduction with plate enlarge

If unstable, fix the plate to one fragment and then reduce the other fragment onto the plate.

4 Plate length and number of screws top

Plate length and number of screws enlarge

In the forearm, three bicortical screws are suggested in each main fracture fragment due to the high torsional stresses.

Not every plate hole needs to be occupied by a screw.

In short oblique forearm shaft fractures an empty plate hole may be necessary at the level of the fracture.

 

5 Fixation top

Prebending the plate enlarge

Prebending the plate

After the plate has been contoured anatomically to the reduced bone surface, prebend it with the handheld bending pliers, or a pair of bending irons, as explained in the principles section.


Insertion of 1st screw enlarge

Insertion of 1st screw

Fix the prebent plate to one of the main fragments with a screw in neutral mode.

Place a reduction forceps on the opposite fragment to hold it in the reduced position against the plate.


Insertion of 2nd screw eccentrically enlarge

Insertion of 2nd screw eccentrically

Insert a second screw eccentrically into the opposite fragment.

By tightening the eccentrically inserted screw, axial compression is achieved.


Insertion of additional screws enlarge

Insertion of additional screws

Additional screws in each fragment are usually inserted in a neutral position.

However, should it be necessary to increase the axial compression, a second screw can be inserted eccentrically into either fragment.

As the second eccentric screw is tightened, the first screw in the same fragment should be loosened slightly to allow the plate to slide on the bone.


Completed osteosynthesis enlarge

Completed osteosynthesis

Before inserting additional screws check reduction of the fracture and rotation of the forearm.

All other screws are inserted in a neutral position and do not produce additional compression.

6 Final assessment top

Radiological confirmation enlarge

Check the completed osteosynthesis with image intensification. These images should be retained for documentation or alternatively an x-ray should be obtained before discharge.

Make sure that the plate is at the correct location, the screws are of appropriate length and the desired reduction has been achieved.


Check the forearm rotation. enlarge

Stabilize the elbow at the epicondyles and check the forearm rotation.

v1.0 2018-11-28