Executive Editor: Peter Trafton

Authors: Rahul Banerjee, Peter Brink, Matej Cimerman, Tim Pohlemann, Matevz Tomazevic

Pelvic ring - Pubic ramus, Pubic ramus plate

back to skeleton

Glossary

1 Introduction top

enlarge

Fractures of the pubic rami are nearly always associated with further pelvic ring injuries. The treatment of these fractures is guided by the displacement and other associated pelvic ring injuries.

In many cases, a strong periosteum, the inguinal ligament and the pectineal ligament will provide adequate stability and no additional treatment is required. With more complex, unstable pelvic ring injuries, ramus fractures may require fixation to restore stability and promote healing.

The decision for operative vs. nonoperative is best made by evaluating the entire pelvic ring and its stability instead of focusing only on the ramus fracture.  

For more complex injuries, posterior reduction and fixation must precede fixation of the ramus fractures. In these cases, the anterior fixation supplements and stabilizes the posterior fixation.


Options for fixation

Stabilization of ramus fractures can be performed by a variety of techniques:

  • Internal fixation with an intramedullary screw
  • Internal fixation with a plate
  • Indirect stabilization with external fixation

For plate fixation, open anatomic reduction is desired. Typically, 3.5 mm reconstruction plates are utilized. Alternatively, any appropriate pelvic plate can also be used.

In osteoporotic bone and in comminuted fractures, angular stable plates are preferred.

The decision to use this technique is based on the pelvic injury pattern, nature of the ramus fractures, and the surgeon's comfort with the anatomy and imaging.

2 Open reduction top

enlarge

After adequate exposure of the fracture site is gained through an anterior approach, bone holding forceps are used to reduce the fracture by direct manipulation.


enlarge

Reduction is verified by direct vision as well as with image intensifier using inlet and outlet views.


enlarge

enlarge

If anatomic reduction is not possible in comminuted fractures, a bridging technique with an appropriately contoured plate is used.

Note

Be alert for rotational malalignment of the fracture. This can be corrected by derotation by bone holding forceps.

3 Fixation top

enlarge

Fixation of oblique fractures

When anatomic reduction is achieved, K-wires are inserted perpendicular to the fracture plane to fix the fracture temporarily.


enlarge

Insert the lag screw as perpendicular as possible to the fracture line.


enlarge

Place an appropriately contoured neutralization plate on the superomedial surface of the superior pubic ramus and fix it.


enlarge

Fixation of transverse fractures

If the reduced fracture is stable, it will provide a template for appropriate contouring of the plate.

Remember to achieve compression of the transverse fracture by slightly underbending the plate which is being applied to a concave surface.


enlarge

The plate is placed superomedial on the superior pubic ramus and inserted in compression mode.


enlarge

Fixation of comminuted fractures

In comminuted fractures it is important to evaluate the overall geometry of the pelvis. 

When acceptable reduction of the pubic rami is achieved, an appropriately contoured plate is inserted as a bridging plate, superomedially on the superior pubic ramus. 


enlarge

Comment to medial and lateral fractures

In medial fractures, it is possible to fix the plate to the ramus alone, both medially and laterally. At least two screws should be inserted on each side of the fracture line.

Extension of the plate across the symphysis to gain additional screws is possible if fixation is poor.


enlarge

In lateral fracture patterns of the superior ramus, the lateral end of the plate should be fixed posterior to the acetabulum, as illustrated.


enlarge

Verification of screw position

The position of each screw should be verified by C-arm to prevent screw penetration into the symphysis or the acetabulum.

Lateral screw positions are verified in the obturator and the iliac wing view.

The medial screws are verified using inlet and outlet views.


enlarge

X-rays

After completion of internal fixation, confirm the final reduction and hardware position intraoperatively by AP, inlet and outlet radiographic imaging.

v1.0 2015-12-10