Executive Editor: Peter Trafton

Authors: Rahul Banerjee, Peter Brink, Matej Cimerman, Tim Pohlemann, Matevz Tomazevic

Pelvic ring - SI-joint, Anterior ORIF SI fracture

back to skeleton

Glossary

1 Introduction top

enlarge

Types of sacroiliac joint instability

Sacroiliac joint instability may be produced by pure dislocations (I), or fracture dislocations involving either the ilium (II) or the sacrum (III)

Instability of the sacroiliac joint occurs most commonly with a pure disruption of the sacroiliac joint.


enlarge

Crescent fracture-dislocation

A crescent fracture is a fracture dislocation of the SI joint.


This injury involves a ligamentous disruption of the inferior part of the SI joint, and a vertical fracture of the posterior ilium that extends from the SI joint and exits the iliac crest.

The posterior superior iliac spine remains firmly attached to the sacrum via the superior portion of the posterior ligamentous complex.
The remaining anterior fragment is more mobile to internal rotation but remains relatively stable to external rotation and vertical forces.

This fracture is always combined with an injury to the anterior pelvis, most often fractures of the pubic rami.

These fractures are unstable.

2 Cleaning of the fracture site top

enlarge

Elevation of the sacroiliac ligament

Use a Cobb elevator to elevate the anterior fibers of the sacroiliac ligament from the sacrum. Further medial dissection must respect the L5 nerve root but can be extended 1-2 cm and should be subperiosteal.


Intraoperative view enlarge

Intraoperative view


enlarge

Prepare the sacral screw insertion

Insert sharp Hohmann retractors posteriorly and anteriorly into the sacrum to expose approximately 1-2 cm of the lateral section of the sacrum for later screw positioning.

The pointed tips of these retractors may be gently impacted into the bone of the sacral ala.


enlarge

The SI joint is distracted using a laminar spreader. The joint is inspected, irrigated, and small fragments are removed.

3 Reduction top

enlarge

Reduction techniques

Reduction is performed using the following techniques:

  • Applying manual lateral compression
  • Use of longitudinal traction 
  • Use of pointed reduction forceps applied on the iliac crest.
  • Use of pointed reduction forceps applied on the sacrum
  • Use of a Jungbluth or Farabeuf clamp applied across the sacroiliac joint.

enlarge

Additional pointed reduction forceps may be applied when necessary to reduce the joint.


enlarge

Reduction using a Farabeuf or Jungbluth clamp

In order to apply the Farabeuf or Jungbluth clamp a screw is placed into the sacral ala. First, the drill hole is made. The drill is placed parallel to the SI joint under direct vision.

These screws are usually 50-60 mm in length.

There is a limited area (approximately 1-2 cm medial to the SI joint) that allows for safe placement of screws in the sacral ala, due to the proximity of the L5 nerve root.


enlarge

Insert a screw into the sacral ala using the previously drilled hole. A second hole is drilled in the ilium just lateral to the sacroiliac joint. Insert a second screw into this hole.

These screws should be placed in the central portion of the sacroiliac joint (from anterior to posterior) in order to leave room for plate(s) anteriorly and in some cases posteriorly to the reduction screws.


enlarge

Next, apply a Farabeuf or Jungbluth clamp to these screws. The clamp can then be used to reduce the sacroiliac joint. The clamp allows for reduction in multiple planes.

Anatomic reduction should be confirmed by direct visualization and verified by image intensification.

4 Fixation top

enlarge

Drilling of the sacral screw

Drill a hole in the lateral part of the sacrum (close to the linea terminalis) directly parallel to the SI-joint using a 3.2 mm drill bit.

Alternatively small fragment plates may be considered.


enlarge

Plate application

Apply a 4.5 mm 3-hole DC-plate for dynamic compression.

The plates are contoured using a table top bending press. The plates are contoured to fit across the SI joint with one screw in the sacrum and two in the ilium.


enlarge

Precontour the plate in the direction of the pelvic brim (linea terminalis) and apply the cortical, sacral screw.

The sacral screw hole is drilled carefully, to avoid injury to the lumbosacral nerve trunk but not enter the sloping SI joint. This screw is inserted and tightened in the neutral position.


enlarge

The medial iliac screw is inserted in compression. Then the lateral screw is inserted in neutral.


enlarge

Screw fixation of the iliac crest

The fracture of the ilium is stabilized with a 3.5 mm intramedullary screw


enlarge

Repeat this procedure for insertion of a second screw, if needed.


enlarge

X-rays

After completion of internal fixation, confirm the final reduction and hardware position intraoperatively by AP, inlet and outlet radiographic imaging.

v1.0 2015-12-10