Executive Editor: Peter Trafton, Michael Baumgaertner

Authors: Peter Kloen, David Ring

Proximal forearm Ulna, extraarticular, simple

back to skeleton

Glossary

1 General considerations top

Ulna oblique metaphyseal – Lag screw with protection plate enlarge

Compression with lag screw and protection (neutralization) plate

In an oblique fracture, interfragmentary compression is achieved with a lag screw.

The screw thread pulls the opposite bone fragment towards the head of the screw, compressing the fracture. On the near cortex, the thread of the screw turns freely, without purchase. Lag screws should be inserted as perpendicularly as possible to the fracture plane, to produce compression without displacement of the fracture.


Ulna oblique metaphyseal – Lag screw with protection plate enlarge

Lag screw osteosynthesis alone is not able to resist functional loading. Therefore, a neutralization plate must be added to allow early mobilization.

Note: Whenever possible (considering soft-tissue condition, fracture configuration, associated radial head fracture etc), position the plate so a lag screw can be inserted through it. This offers improved stability.


Ulna oblique metaphyseal – Lag screw with protection plate – Plate selection enlarge

Choosing the right plate

Use a six or seven-hole plate, depending on the fracture configuration. Usually, three screws in each fragment provide sufficient stability.

These plates plate may be used:

  • Small fragment dynamic compression plate (3.5 DCP),
  • Limited contact dynamic compression plate (LC-DCP)
  • Specific proximal ulna prebent plate
  • Locking plate (LCP) may be used in osteoporotic bone.

Ulna oblique metaphyseal – Lag screw with protection plate – Plate contouring enlarge

Prebending and contouring

Prebend the plate according to the surface anatomy of the ulna if needed.

Contouring of the plate is achieved with bending irons or a bending press.


Ulna oblique metaphyseal – Lag screw with protection plate – Plate position enlarge

Plate position

The plate is placed on the posterior aspect of the ulna. This is the tension side of the bone and the plate will resist deforming forces best when placed here. Make sure that the proximal screws do not protrude into the joint.


Ulna oblique metaphyseal – Lag screw with protection plate - Osteoporosis enlarge

Note: To improve proximal stability (short fragment and/or osteoporosis) a posterior plate can be curved around the olecranon and anchored with an axial screw.

2 Reduction and preliminary fixation top

Ulna oblique metaphyseal – Lag screw with protection plate – Cleaning fracture site enlarge

Cleaning of the fracture site

Expose the fracture ends with minimal soft tissue dissection off the bone.

Remove hematoma and irrigate.


Ulna oblique metaphyseal – Lag screw with protection plate – Direct reduction enlarge

Direct reduction

Reduce the fracture with the help of small pointed reduction forceps and provisionally fix with forceps or K-wires.

3 Lag screw insertion top

Ulna oblique metaphyseal – Lag screw with protection plate - Drilling enlarge

Drilling

Drill a 3.5 mm gliding hole for the lag screw into the posterior cortical bone of the distal fragment.

Insert the 2.5 mm drill sleeve into the gliding hole until it reaches the far cortical bone.

Now drill the far cortex with the 2.5 mm drill bit.

Countersink the cortex of the distal fragment in order to have more surface area to distribute the force caused by the head of the lag screw.


Ulna oblique metaphyseal – Lag screw with protection plate - Measuring enlarge

Measuring

Measure the depth of the hole with the hook of the depth gauge pointing proximally.


Ulna oblique metaphyseal – Lag screw with protection plate – Lag screw insertion enlarge

Lag screw insertion

Closely observe the compression effect on the fracture line while tightening the lag screw.

The reduction forceps should be removed just before the final tightening of the screw.

4 Protection plate top

Ulna oblique metaphyseal – Lag screw with protection plate – Plate fixation enlarge

Plate fixation

Apply the contoured plate and fix it to the bone with three screws proximal and three screws distal to the fracture in neutral position to protect the lag screw.


Ulna oblique metaphyseal – Lag screw with protection plate enlarge

Final assessment

Finally, assess the range of motion in pronation, supination, flexion and extension.

Check results with image intensifier or x-ray.

v2.0 2018-04-30