Executive Editor: Joseph Schatzker

Authors: Jonas Andermahr, Michael McKee, Diane Nam

Scapula Glenoid fossa, complete articular, articular simple, neck simple

back to skeleton


1 Introduction top

Principle enlarge


In this procedure it is important to anatomically reconstruct the joint surface, and thereby convert the complete articular fracture type to an extra-articular fracture type.

The joint block is then reduced to the scapular body.

One must restore the correct anatomical angle between the glenoid fossa and the scapular body.

Plate selection enlarge

Plate selection

The standard plate for this fixation is the 2.7 or a 3.5 reconstruction plate.

2 Patient preparation top

This procedure may be performed with the patient in either a prone position or lateral decubitus position.

3 Approach top

Principle enlarge

Plating of the glenoid neck and scapula are performed through a posterior approach.


In a complete articular fracture with an anterior fragment a posterior arthrotomy is necessary to reduce the fragment. Its fixation is achieved with a lag screw inserted posteriorly.

4 Restoration of articular surface top


Reduction of the joint surface using K-wires

Reduction of the articular surface may be facilitated by the insertion of a K-wire to be used as joystick. The use of a cannulated system is preferred. Therefore, insert the K-wire for the potential cannulated screw in the planned lag screw trajectory.


When reduction of the articular surface is completed, insert the K-wire further to temporarily fix the articular fracture.


Alternatively, a repositioning clamp can be used to reduce the fragments of the glenoid fossa.


If possible, the fracture of the glenoid fossa should be fixed with a lag screw(s).

Once the articular fracture is fixed, proceed with the fixation of the neck as for simple extra articular fractures.

5 Reduction and fixation of the glenoid neck using reconstruction plate top


The articular segment is now fixed. Once the neck fracture is reduced, it is best to use cortical screws for fixation of the plate into the articular segment to bypass the inserted lag screw.

One or two K-wires are partially inserted in the articular block and used as a joystick for reduction.


The joint block is reduced to restore the anatomical angle of the glenoid fossa. Large deviations of the angle (>20 °) will reduce the functional outcome.

If the reduction is not successful, an alternative procedure where the plate is used as a reduction aid can be employed (see below)

K-wires are inserted for temporary fixation. Care should be taken that the position of the K-wires does not interfere with the planned position of plate and screws.


Plate fixation

The reconstruction plate is shaped to a near perfect anatomical fit.


At least two screws are necessary for sufficient fixation of the glenoid joint block.

Ideally, three bicortical screws are inserted in the lateral scapular border. If the bone stock is poor, locking screws are indicated.

6 Alternative reduction and fixation using an angle stable plate top


It is best to use a reconstruction plate designed to take angularly stable screws.

The plate is bent at the right spot to subtend the usual angle between the glenoid and the lateral border of the scapula (130 - 135 degrees).

Up to 10 degrees deviation from the anatomically correct angle can be tolerated.

When angularly stable fixation is used the plate does not have to fit the bone, but must fit the overall contour.


The plate is fixed to the glenoid segment with two bicortical screws.

If locking screws are used, care must be taken regarding their direction so that they do not enter the joint.


In a transverse fracture of the glenoid where lag screw fixation is physically not possible, maintain reduction and compression of the fracture with a clamp, then reduce the neck fracture.

The reduction and compression of the articular fracture is then maintained by the fixation of the plate to the articular segment.


The plate is then used as a reduction aid. 

A trasglenoid X-ray is recorded to verify whether the anatomical angle is achieved.

Large deviations of the angle (>20°) will reduce the functional outcome.

When the correct reduction and the correct angle between the glenoid fossa and the lateral border of the scapula have been achieved, screws are inserted along the lateral border of the scapula.


Correct reduction and fixation is verified by image intensification.