1 Introduction topenlarge
The aims of surgery are to:
- improve the spinal curve,
- improve the three dimensional alignment of the spine,
- prevent progression of the curve in the future
- improve cosmesis
- reduce pain
- optimize pulmonary function
- maintain neurological integrity.
This is achieved by correction of the deformity and creation of a solid arthrodesis of the deformed part of the spine.
To illustrate this procedure, we will use a right thoracic curve.
2 Hook/screw configuration and placement topenlarge
The hook configuration and placement may vary depending on levels to be fused. We will here illustrate the principle in a typical T5 to L1 fusion in a right thoracic curve.
If for any reason a pedicle screw or hook is not feasible, one may consider the use of sublaminar cables or wires as a substitute. However, compressions and distractions will not be possible with these implants.
In general, pedicle screws should be used for lumbar segments and hooks for thoracic segments.
Pedicle screw placement
Pedicle screws are placed in the LIV.
Left side hook placement
For distraction between T5 - T12, and compression between T12-L1, the following hooks are planned:
- Cranially pointing pedicle hooks at T5 and T7.
- Caudally pointing supralaminar hooks at T10 and T12.
Hook sites are prepared and tested for stability. The hooks are then removed avoid inadvertent damage to the dura during preparation of other anchor sites.
Right side hook placement
For compression between T5 – T11- L1 the following hooks are planned:
- Caudally pointing transverse hook at T5
- Cranially pointing pedicle hook at T6
- Cranially pointing pedicle hook at apex (T8)
- Cranially pointing sublaminar hook at T11
Hook sites are prepared and tested for stability. The hooks are then removed to avoid inadvertent damage to the dura during preparation of other anchor sites.
3 Release top
Indications for release
Depending on flexibility findings, the release can be carried out only at the apex of the curve, which is usually the stiffest, or the whole length of the instrumented spine.
A release is generally performed if the spine cannot easily align to the rod during surgery. This can be predicted preoperatively based on the bending X-ray. For stiff curves, fulcrum bending X-ray and the traction X-ray under general anesthesia is the method of choice for determining flexibility.
A soft tissue release can be performed by removal of the interspinous ligaments along with the midline ligamentum flavum of the apical regions of the deformity. If additional release is desired, then formal Posterior Column Osteotomy (PCO) can be performed at the same levels. PCO is also called SPO (Smith-Petersen osteotomy) or Ponte osteotomy. The shaded area to the left outlines the bony resection performed during a PCO.
All posterior releases begin by resecting the inferior aspect of the spinous process, followed by removal of the interspinous ligament utilizing a standard rongeur.
Removal of the 3-5 mm of the inferior aspect of the inferior facet joint is performed at each level of the planned fusion using an osteotome.
The ligamentum flavum is removed with a Kerrison rongeur beginning in the midline and exiting lateral until abutting against the medial aspect of the superior facet. It is important not to penetrate deeply against the dura or tear the dura.
Care should be taken not to tear the dura particularly on the concavity of the curve where the neuro tissues preferentially lie.
A Kerrison rongeur is utilized to remove the most cephalad portion of the superior articular facet exiting out lateral into the neuroforamen. This completes the PCO and is usually repeated at other levels.
Epidural bleeding within the neuroforamen is controlled with hemostatic agents and cottonoid packing.
4 Facet joint fusion topenlarge
The inferior articular facet is removed with an osteotome exposing the articular cartilage of the superior articular facet.
Remove the articular cartilage from the superior articular facet using a gouge or a curette.
Insert pieces of bone graft (autograft, allograft, or bone substitute) into the decorticated facet joint for arthrodesis.
These steps are repeated for all the levels on both sides.
5 Hook insertion topenlarge
The hooks are inserted in the prepared sites as planned.
6 Left rod topenlarge
The concave rod is bent to the appropriate thoracic kyphosis as preoperatively planned with the appropriate transition into lordosis of the thoracolumbar junction as necessary.
The amount of thoracic kyphosis bent into the left rod will be based on:
- curve size
- curve flexibility
- number and purchase of bone anchors
- size and material of the rod utilized.
Starting with the most cranial hook the rod is inserted into all concave hooks and screw conforming to the concavity of the deformity without being locked.
One should ensure that the hooks do not back out during rod rotation. A temporary C clip or rod grippers may be applied behind the hooks to prevent this.
Rod holders are then applied onto the rod and the rod is rotated 90° counter-clockwise around its axis converting the scoliosis into kyphosis.
This rod-rotation maneuver should be performed slowly and cautiously with careful attention to both the implant-bone interface to avoid pullout, and to the neuromonitoring signals.
The rod is now locked to the caudal screw to prevent the rod from rotating back.
Distraction of the concave thoracic curve
Distraction is first performed between T7 and T10 followed by locking of these two hooks.
Distraction is then performed between T5 and T12 followed by locking of these two hooks.
Restoration of thoracolumbar transition
The L1 screw is now loosened, and compression is then performed between T12 and L1 to restore the thoracolumbar lordotic transition. The L1 screw is then re-locked.
7 Right rod topenlarge
The right rod is bent to slightly less kyphosis compared to the concave side.
The rod is attached to both the T5 transverse and T6 pedicle hook, rotated into its normal sagittal position and then compressed to create a stable claw configuration.
The distal end of the rod is then levered down using a rod holder and sequentially attached to the T8 and T11 hooks and the L1 screw.
This maneuver will push the apical hump anteriorly, thereby achieving derotation of the apical segments.
Compression is then performed between T5 - T8 (1) and T5 - T11 (2). Distraction is performed from T11 – L1 (3) achieving further correction of the scoliosis and vertebral derotation. This is followed by final tightening of all hooks and screws.
8 Spinal fusion topenlarge
The laminae and the transverse processes are decorticated with an osteotome.
Care should be taken to always point the osteotome away from the spinal canal.
Alternatively, the decortication may be performed with a powered burr.
Bone graft (allograft, autograft, or bone substitutes) is copiously placed over the entire decorticated area.
9 Transverse rod connectors topenlarge
Transverse connectors are then inserted one at each end of the construct.
10 Intraoperative imaging top
At some point prior to wound closure intraoperative imaging should check:
- Fusion levels
- Screw position
Overall coronal and sagittal correction and alignment