1 Introduction topenlarge
The aims of surgery are to:
- improve the spinal curve
- improve the three dimensional alignment of the spine
- prevent progression of the curve in the future
- improve cosmesis
- reduce pain
- optimize pulmonary function
- maintain neurological integrity
This is achieved by correction of the deformity and creation of a solid arthrodesis of the deformed part of the spine.
For this procedure we will assume a left lumbar curve.
2 Pedicle screw insertion topenlarge
Pedicle screws can be inserted into every second or into every level depending on surgeon's preference.
In the case of very stiff curves, screws may be inserted into every level.
3 Release top
Indications for release
Depending on flexibility findings, the release can be carried out only at the apex of the curve, which is usually the stiffest, or the whole length of the instrumented spine.
A release is generally performed if the spine cannot easily align to the rod during surgery. This can be predicted preoperatively based on the bending X-ray. For stiff curves, fulcrum bending X-ray and the traction X-ray under general anaesthesia is the method of choice for determining flexibility.
A soft tissue release can be performed by removal of the interspinous ligaments along with the midline ligamentum flavum of the apical regions of the deformity. If additional release is desired, then formal Posterior Column Osteotomy (PCO) can be performed at the same levels. PCO is also called SPO (Smith-Petersen osteotomy) or Ponte osteotomy. The shaded area to the left outlines the bony resection performed during a PCO.
All posterior releases begin by resecting the inferior aspect of the spinous process, followed by removal of the interspinous ligament utilizing a standard rongeur.
Removal of the 3-5 mm of the inferior aspect of the inferior facet joint is performed at each level of the planned fusion using an osteotome.
The ligamentum flavum is removed with a Kerrison rongeur beginning in the midline and exiting lateral until abutting against the medial aspect of the superior facet. It is important not to penetrate deeply against the dura.
Care should be taken not to tear the dura particularly on the concavity of the curve where the neuro tissues preferentially lie.
A Kerrison rongeur is utilized to remove the most cephalad portion of the superior articular facet exiting out lateral into the neuroforamen. This completes the PCO and is usually repeated at other levels.
Epidural bleeding within the neuroforamen is controlled with hemostatic agents and cottonoid packing.
4 Facet joint fusion topenlarge
In cases where a PCO has been performed, the facet joint is already removed and this step ("Facet joint fusion") should be omitted.
The inferior articular facet is removed with a osteotome exposing the articular cartilage of the superior articular facet.
Remove the articular cartilage from the superior articular facet using a gouge or a curette.
Insert pieces of bone graft (autograft, allograft, or bone substitute) into the decorticated facet joint for arthrodesis.
These steps are repeated for all the levels on both sides.
5 Rod insertion topenlarge
The left rod is bent to the appropriate lumbar lordosis as preoperatively planned with the appropriate transition into kyphosis in the thoracolumbar junction as necessary.
The amount of lumbar lordosis bent into the left rod will be based on:
Curve size, curve flexibility, number and purchase of bone anchors, size and material of the rod utilized.
Starting with the most cranial screw the rod is connected sequentially into all the screws on the left side of the lumbar curve conforming to the convexity without being locked.
Rod holders are then applied onto the rod and the rod is rotated 90° counter clockwise around its axis converting the scoliosis into lordosis.
This rod-rotation maneuver should be performed slowly and cautiously with careful attention to both the implant-bone interface to avoid pullout, and to the neuromonitoring signals.
The rod is locked to the most caudal screw to prevent it from rotating back. The other screw heads are kept unlocked.
The right rod is bent to slightly less lordosis compared to the left side.
The right rod is attached to the most cranial screw in its normal sagittal-plane rotation and locked.
The distal end of the rod is then levered down using a rod holder and sequentially attached to the remaining screws, starting cranially.
On attaching the right rod to the concavity, the lumbar segment will be lifted dorsally and partially derotated.
6 Compression and distraction topenlarge
Compression on the convex side of the lumbar curve
Attention is now returned to the left side. After locking the apical screw to the rod, compression is applied towards the apex for both the cranial and caudal screws locking them to the rod along the way.
Distraction on concave side of the lumbar curve
Attention is now returned to the concave lumbar side. After locking the apical screw, gentle distraction away from the apex is applied to the cranial and caudal screws as they are being locked.
Over distraction should be avoided because it will flatten the lumbar lordosis.
7 Spinal fusion topenlarge
The laminae and the transverse processes are decorticated with an osteotome.
Care should be taken to always point the osteotome away from the spinal canal.
Alternatively, the decortication may be performed with a powered burr.
Bone graft (allograft, autograft, or bone substitutes) is copiously placed over the entire decorticated area.
8 Transverse rod connectors topenlarge
Transverse connectors are then inserted one at each end of the construct.
9 Intraoperative imaging top
At some point prior to wound closure intraoperative imaging should check:
- Fusion levels
- Screw position
Overall coronal and sagittal correction and alignment