1 Introduction topenlarge
B2 injuries indicate a bony and/or ligamentary failure of the posterior tension band together with a Type A fracture of the vertebral body. Type A fracture should be classified separately as management depends on both.
In cases where neurological deficit is observed and compression of the spinal canal is assumed, decompression has to be performed. It should be understood that this is a step that can also result in deterioration of neurology unless very meticulously performed.
Decompression can be performed anteriorly or posteriorly. Posteriorly decompression can be indirect or direct.
Indirect decompression may be tried before performing direct decompression.
Please refer to Decompression techniques for a detailed discussion of indications for the posterior decompression techniques. ( Posterior decompression)
2 Closed reduction topenlarge
Primary reduction is performed by positioning of the patient onto a frame to create lordosis.
3 Reduction with intermediate pedicle screws topenlarge
The addition of intermediate screws provides more biomechanical stability to the construct. In patients with A3/ A4 injury with significant vertebral body comminution and intact pedicles, this technique is preferred, if an anterior reconstruction is not planned.
Due to the fact that bilateral instrumentation is necessary in all cases, all steps described below are repeated on the opposite side, unless described otherwise.
Pedicle screw insertion
Pedicle screws are inserted into the vertebrae cephalad and caudal to the fracture level on both sides. Mono- or polyaxial screws can be used. ( Pedicle screw insertion)
Intermediate screw insertion
Under fluoroscopic guidance, screws are also inserted into the pedicles of the fractured vertebrae ("intermediate" screws). Intermediate screws are inserted in both the pedicles of the fractured vertebra, however if a pedicle (as assessed on the CT scan) is fractured, no screw is inserted into that pedicle. If both the pedicles are injured, then this technique cannot be used.
The intermediate screws are left slightly proud compared to the screws inserted above and below, in order to be able to reduce the fracture later on.
The length of the intermediate screws is generally kept short so that it just enters the vertebral body after crossing the pedicle.
This allows an anterior reconstruction on a later date if required, without disturbing the posterior construct.
The contouring of the rod depends on the site of the fracture. A rod contoured in mild kyphosis is chosen for fractures from T1-T10. A straight or a slightly lordotic rod is chosen for fractures from T11-L1, and a rod contoured to lordosis is chosen for lumbar fractures.
The rod is introduced to the screw heads from distal to proximal and the distal screw head is tightened first. The proximal and intermediate screw heads are kept loose.
The rod is also inserted into the proximal screw heads without tightening.
If decompression is needed, an indirect reduction may be done at this stage. If indirect decompression proves to be insufficient, a direct decompreesion, e.g., posterior or transpedicular decompressions are undertaken. Refer to the Posterior Decompression techniques for detailed instructions. ( Posterior decompression)
With the help of a rod holder and a distractor, the proximal screws are distracted along the rod. This is done on both sides simultaneously.
Pitfall: Avoid overdistraction
Care should be taken to avoid overdistraction in type B2 fractures.
The locking heads of the proximal and intermediate screws are tightened to secure the distraction achieved.
The final construct is shown from a lateral view
4 Fusion top
Although fusion was routinely performed for all spinal fractures, its indications are now being restricted to fractures that are highly unstable.
Nonfusion fixations can be performed for A3, A4, and B1 type injuries.
Fusion is routinely performed for A2, B2, B3, and all C injuries as they are unstable injuries with extensive soft tissue and ligamentous disruption.
If the surgeon plans for a fusion, the facet capsule is excised and the joint cartilage surfaces are denuded/curetted.
Pieces of bone graft (autograft, allograft) are inserted into the decorticated facet joint for fusion.