Executive Editor: Steve Krikler

Authors: Paulo Barbosa, Felix Bonnaire, Kodi Kojima

Malleoli 44-B1.3 Bridging plate

back to skeleton

Glossary

1 Principles top

Bridging

Bridge plating uses the plate as an extramedullary splint, fixed to the two main fragments, while the fracture zone is left virtually untouched.

Reduction of the distal tibiofibular joint is important Therefore, restoration of the length, axis and rotation of the fibula is crucial. and must be checked intraoperatively under image intensification.

Reduction can usually be achieved indirectly by distraction. Anatomical reduction in the fibular fracture zone is not necessary.


Bridging plates are commonly used in B1.3, B2.3, B3.3 and C2 fractures.


Mechanical stability

Mechanical stability, provided by the bridging plate, should be adequate for indirect healing (callus formation).

In cases of large zones of comminution, stronger plates, such as reconstruction plates or locking compression plates (LCP), provide better stability than one-third-tubular plates.

The angular stability provided by the LCP may be advantageous.


enlarge

Mechanical stability (syndesmosis)

In type C fractures (Lauge-Hansen type PE 4), the syndesmosis complex is usually unstable.

2 Reduction top

enlarge

In multifragmentary fractures, care must be taken to avoid excessive stripping of the periosteum as well as devascularization of the fragments.

Indirect reduction may be obtained by longitudinal traction, either on the foot, or of the main distal fragment using a bone hook.

In a B-type fracture, if the distal fragment is large enough, insert one or two K-wires to hold the reduction.

Rotation and anatomical position are difficult to determine. All methods of visualization of the distal tibiofibular joint such as image intensification, and palpation with a finger can be used. It is useful to have a comparative x-ray of the other, uninjured ankle as a template.


enlarge

In a C-type fracture, once the lateral malleolus is reduced in its anatomic position, it may be helpful to insert a K-wire, 30 degrees from dorsal, 2-3 cm supramalleolar.


enlarge

Reduction with the plate

Alternatively, the plate can be used for gaining length after fixing it to the distal fibular fragment (see step 4).

For this purpose, insert a screw into the fibula proximal to the plate and distract the fracture to the correct length with a laminar spreader. When tension on the plate can be felt, secure the plate to the fibula with pointed reduction forceps applied through a hole in the plate.

Check rotation and the position in the incisura fibularis before fixing the plate to the proximal fibula.

3 Plate preparation top

Plate selection

Anatomic plates with locking screw option are available from various manufacturers. To illustrate the principles of the procedure, the use of a classic plate is described.


enlarge

Plate length

The plate must be long enough both to cover the length of the fracture zone and ideally to allow insertion of three screws in each main fragment.


enlarge

Contouring the plate

Before the plate is applied, it must be contoured.

Contouring is best done with the help of the appropriate aluminum template. The plate should perfectly fit the bone contour throughout its entire length.

If a plate with locking screws is used on the shaft of the fibula, it does not have to fit perfectly against the bone.


enlarge

Plate position

Position the plate firmly by hand and plan the position of the first proximal screw near the fracture.

Remove the plate.

4 Fixation B-type fractures top

enlarge

Insertion of first proximal screw

Drill a 2.5 mm hole through both fibular cortices at the planned screw site, 3 mm proximal to the fracture.

Measure the length through the plate, tap with the cortical tap and tap sleeve.

Carefully apply the plate. Insert the first proximal screw.

The screw should just penetrate the far cortex.


enlarge

Insertion of first distal screw

Next, insert a screw into the first distal plate hole. All distal screws are aimed towards the articular surface of the lateral malleolus. Ensure that their tips do not protrude into the joint by aiming the drill slightly posteriorly.

Predrill carefully until just reaching the far cortex. Measure the length and select a 3.5 mm cortex screw approximately 2 mm shorter. Tap threads only in the near fibular cortex, and insert the selected screw.

Note

In osteopenic bone, fully threaded cancellous screws can be used.


enlarge

Completing screw insertion

Insert the remaining screws as described above in the sequence determined by the preoperative plan.

The most distal screw is inserted slightly obliquely from distal to proximal in a posterior direction.

Again choose a screw 2 mm shorter than was measured and tap the threads only in the near cortex.

Gently tighten all screws.

Check under image intensification in both planes and ensure that no screw protrudes into the ankle joint or the syndesmosis.


Pearl: Small distal fragment or osteoporotic bone

Consider using a locking screw in case of a small distal fragment or in severe osteoporotic bone.

v1.0 2006-12-04