Executive Editor: Ernst Raaymakers, Joseph Schatzker, Rick Buckley

Authors: Matthias Hansen, Rodrigo Pesantez

Proximal tibia Complete articular fracture, simple articular, multifragmentary metaphyseal

back to skeleton


1 Principles top

General considerations

Anatomical reduction of the articular surface is mandatory. Reduction of the metaphyseal fracture depends on the degree of comminution. If possible, reduce anatomically but remember that it is more important to retain vascularization of the bony fragments than to achieve their anatomical reduction.

Main steps in treatment include:

  1. Temporary reduction and immobilization until definitive surgery (eg, external fixator).
  2. Adequate preoperative planning (is a bone graft necessary, what type of approach, the number and type of implants, and any additional equipment).
  3. Make an arthrotomy between the meniscus and the tibia. This will allow for adequate visualization of the articular fracture. Inspect the meniscus for any tears. These will have to be repaired at the end.
  4. Anatomical reduction of the articular surface and absolutely stable fixation if possible.
  5. Reduction of the metaphysis and provisional fixation with K-wires.
  6. Definitive stable fixation of the metaphysis using screws and plate(s) with preservation of the blood supply of the metaphyseal fragments.

Timing of surgery

Surgery should be delayed until full recovery of soft tissues (swelling, blisters, abrasions, etc). This takes usually 3 to 10 days.

Until surgery, length of the leg should be maintained (eg, external fixator, traction, etc).

Plate location

Plate location depends on the fracture morphology. The plate is used to buttress the fragments. On the medial side, if the fracture morphology allows, the plate may be placed on the anteromedial surface. Most commonly, the wedge fragment is split off in such a way that to buttress it adequately the plate must be positioned posteromedially.

Double plating enlarge

Double plating

In order to prevent collapse these fractures require buttressing on the medial as well as lateral side. The position of the medial plate will depend on the fracture pattern. Most often it is positioned on the posteromedial crest of the tibia.

Medial or lateral side first?

Most often the medial fragment is less comminuted and should be addressed first to restore the anatomical relationship of the medial joint surface, original length and rotation. Therefore, in the majority of cases the medial approach is carried out first and the medial fracture is reduced and fixed provisionally with a buttress plate with the minimum number of screws necessary. Because occasionally the reduction and fixation of the medial side has to be readjusted as the lateral side dealt with.
The lateral fracture is addressed next. Once a satisfactory reduction and fixation is reached on the lateral side, the fixation on the medial side is completed and the wounds are closed in a routine fashion.

Potential complications

  • Articular damage
  • Vascular and nerve injury (peroneal nerve)
  • Compartment syndrome

Check for these during surgery. Do not close the fascia to prevent compartment syndrome.

2 Preparation top

Patient positioning

Depending on the approach, the patient may be placed in the following positions:

Use of a tourniquet

A tourniquet should be applied in every case. Whether the tourniquet is used depends on the amount of bleeding. Exsanguinate the limb by elevating it.

Use of a radiolucent table

To allow for intraoperative radiographic control of reduction and fixation, the use of a radiolucent table is mandatory.

Preparation for bone graft

If autologous bone grafting is planned the anterior iliac crest should be prepared and draped as well as the limb.

3 Approaches top

Not all complete articular fractures can be perfectly reduced through a medial/posteromedial and/or an anterolateral approach. Sometimes fractures with a flexion injury mechanism need to be addressed through a posterior approach as well.

4 Preliminary reduction top

C2-type fracture enlarge

General consideration

Rotation, length and axial alignment should be restored first by axial traction (distractor, external fixator or manual traction).

Ligamentotaxis helps to achieve preliminari reduction enlarge


Ligamentotaxis helps to achieve preliminary reduction of the main fracture fragments and helps to maintain length during the operation. It is also used preoperatively to maintain provisional reduction.

Use of distractors and external fixators enlarge

Use of distractors and/or external fixators

In order to reduce these complex fractures one may need to use two femoral distractors one on the medial and one on the lateral side. To do this place the knee in slight flexion.

One can also achieve the same with the use of two external fixators or one distractor and one external fixator. The use of the external fixators makes intraoperative adjustments almost impossible because they do not allow for rotational or angular correction.

Use of distractors and external fixators enlarge

Distractors, because they apply the force directly to the bone, are very powerful and make distraction easy. Use the distractor on the side with more comminution. Usually, the medial side can be managed with an external fixator because it is usually less comminuted. If only external fixators are available, place one on the medial and one on the lateral side or span the knee joint anteriorly with a unilateral frame.

5 Reduction of the articular surface top

Reduction of the articular surface with clamps enlarge

Reduction of the articular surface with clamps

In rare situations where the articular fragments are large, their reduction may be achieved by percutaneous manipulation with clamps and joy sticks. Most often, the joint has to be exposed in order to achieve an anatomical reduction. If only percutaneous manipulation is used, reduction must be checked with either a C-arm or an arthroscope.

Clamp over plate enlarge

Pearl: clamp over plate

If you intend to keep the clamp on throughout the whole procedure, it is best to slip the plate under the clamp prior to its tightening to maintain reduction. From your preoperative plan and/or intraoperative trail you will know which screw hole is best for placement of the clamp.


Secure reduction

Once reduced, secure the provisional fixation with K-wires.
Verify the reduction with the help of image intensification.

6 Medial column fixation top

Plate application on medial side enlarge

Plate application on medial side

A medial plate is applied and secured with screws. Some of these may be only unicortical if fixation is meant to be provisional.

7 Lateral column fixation top

Placement of lag screw enlarge

Placement of lag screw

The placement of the lag screw or screws used to achieve absolute stability of the articular surface is determined by the fracture pattern. Ideally, these screws should be inserted at right angle to the fracture plane.

The buttress plate, once properly contoured, is inserted on top of the periosteum deep to the muscle envelope. The most proximal screw if it fits with the fracture morphology may be a lag screw.

Click here for a detailed description of the lag screw technique.

Additional screw placement enlarge

Additional screw placement

K-wires may be removed once fixation is achieved. The number of screws on each side of the fracture depends to some degree on the fracture configuration. Distal to the fracture, one should aim for at least two to three cortex screws for plate fixation to the distal fragment.

Final osteosynthesis enlarge

Final osteosynthesis

At the end, once stable fixation has been achieved and checked with the image intensifier, remove the distractor(s).

8 Alternative: angular stable plate top

Alternative: angular stable plate enlarge

If one is using a plate with the possibility of angular stability like the lateral tibial plate with locking screws or the LISS for the tibia and the fracture configuration is such on the medial side that once reduced there is inherent stability, one can consider to leave out the medial plate.

v2.0 2010-05-15